Fender trimming

[cherokee-at-16]

I can get front pacer flexy flares at 4.5" wide for 52$...Mom Most likely will not like there being no flares.

What does "DANA 30 Reverse" mean compared to "DANA 30 Standard"
And what is a carriar...what does it do, how do you know if you need a new one when regearing.

[cherokee-at-16]

Quess im going to be cuten them fenders sooner then i thought. Just got into a fight with a 2000 Ranger but my 2000 cherokee got the best of him. Cop talked to the witness after he said we could leave, but the witness was my friend and my dad stayed to hear what was said...If we talked to him first maybe me being at falt would be the other way!!! Btu officer already wrote it down and the other guy took off...o well

Only damage was to what i was going to cut off

BTW how do you post pics

[Burton58]

the low pinion dana 30 (2000-2001 cherokee) uses standard cut gears. all the high pinion dana 30's run reverse cut. the carrier needs to be changed in the front axle when going lower than 3.73 gears. since you are most likely going to 4.56 you need a new open carrier. depending on which rear axle you have you might need that too

[LittleD]

make urself a photobucket account, upload the pics to there and then use one of the links under the picture. (i think it's the embed one)

[cherokee-at-16]

Damage from incident..plan to cut most of it off anyway..justifies cuting a clean jeep up pullen the fender off it was just floppen around ....how do you get off teh thing that hold the flares on?

ms/zz106/Cherokee-at-16/IMG_2848.jpg[/IMG]

[Magilla]

please go make an introduction

[cherokee-at-16]

? Whats that...i will do that but dont know what it is?

[jeepbogger4x4]

newbie forum.

[cherokee-at-16]

Go there and do what? Ill go check it out................done

[Bigbike]

That will cut right out. no worries.

[cherokee-at-16]

Any one know what axles bolt up to the cherokee

[JoeNitro]

have fun.

http://sisoffroad.com/forums/showthread.php?t=11

[XJtheXtremeJeep]

Any one know what axles bolt up to the cherokee

A LJ or TJ dana 44 for the front, or any dana 30 out of a zj, xj, mj, lj, tj and for the rear a xj dana 44, a xj dana 35, or a 8.25. the dana 44s are the two strongest that will just bolt in but expect to pay alot of money for a tj or lj 44 front, and be prepared to do onboard air if you want to use the factory selectable locker..... also these have the same bolt pattern as eachother, if your looking for axles to swap in the ford 8.8 requires some work but will have the 5 on 4.5 bolt pattern and possibly disk brakes.

Also there are some other axles that can be made to bolt in relativly easily

[Ktmracer419]

Any one know what axles bolt up to the cherokee

cherokee fronts, cherokee rears
tj wrangler fronts
zj grand cherokee fronts

[Krazors001]

[QUOTE=cherokee-at-16;138937Damage from incident..plan to cut most of it off anyway..justifies cuting a clean jeep up pullen the fender off it was just floppen around ....how do you get off teh thing that hold the flares on?
[/QUOTE]

There are 10mm bolts on the inside of the fender. You'll want to either trim or pull out the mud guard in there. I just tossed mine because it fell off