Tweet
Bringing this over here because i hope to do more work on this pile. Maybe i could use some motivation.
how it looked when i pulled it in
pile oh shit
all torn down
found rot on 4 spots in frame
patching
plasma's rule
all patched up
brackets
rear in
front in
track bar bracket
setting the track (used a plumb bob)
sick miller tig/stick
poser shots
STATS
1" mml
2" body
(wa son jeep when i got it)
3" saggy prings
3/4" spacers
36"x13.5" irok bias
waggy 44 front 4:56 and detroit w/ford hubs 5x5.5 (thanks steve)
tj rear 44 4:56 detroit warn chromo full float kit amc20 drums 5x5.5(thanks steve)
both axles with clayton high clearence brackets and truss
clayton long arm and t-case skid
rock rails made outa f-350 front cross members
gas tank in the rear
over the knuckle steering
header with cat/muffler welded directly behind it
um thats about it. i have more i need to do but i need to find access to a tube bender first (looks in daves direction)
NEED: cage, flat fenders, grill hoop, on-board air
WANT: winch and 4:1 t-case gears, also drop it down to 1" bl, and get 3.5" springs instead of the 3" with 3/4" spacers
how it looks at the moment:
WHATS NEXT?
Cage - Have it, just got to install with soem modifications.
Rocker protection - i removed my old frame mounts, and got some PS ones that I am modding a step/slider onto.
Tube Work - grill hoop tided into fender flairs.
Stretch - got to move the coil buckets back and outboard my shocks in the rear.
now i just need to get off my ass for this stuff to happen. Any comments would be cool to get me motivated, lol
how it looked when i pulled it in
pile oh shit
all torn down
found rot on 4 spots in frame
patching
plasma's rule
all patched up
brackets
rear in
front in
track bar bracket
setting the track (used a plumb bob)
sick miller tig/stick
poser shots
STATS
1" mml
2" body
(wa son jeep when i got it)3" saggy prings
3/4" spacers
36"x13.5" irok bias
waggy 44 front 4:56 and detroit w/ford hubs 5x5.5 (thanks steve)
tj rear 44 4:56 detroit warn chromo full float kit amc20 drums 5x5.5(thanks steve)
both axles with clayton high clearence brackets and truss
clayton long arm and t-case skid
rock rails made outa f-350 front cross members
gas tank in the rear
over the knuckle steering
header with cat/muffler welded directly behind it
um thats about it. i have more i need to do but i need to find access to a tube bender first (looks in daves direction)
NEED: cage, flat fenders, grill hoop, on-board air
WANT: winch and 4:1 t-case gears, also drop it down to 1" bl, and get 3.5" springs instead of the 3" with 3/4" spacers
how it looks at the moment:
WHATS NEXT?
Cage - Have it, just got to install with soem modifications.
Rocker protection - i removed my old frame mounts, and got some PS ones that I am modding a step/slider onto.
Tube Work - grill hoop tided into fender flairs.
Stretch - got to move the coil buckets back and outboard my shocks in the rear.
now i just need to get off my ass for this stuff to happen. Any comments would be cool to get me motivated, lol
hows that D44a installation going 
oh and i had to notch the rear cross member to get 6"
Comment